导航:首页 > 版本升级 > puttyttl传文件

puttyttl传文件

发布时间:2025-10-13 12:48:15

Ⅰ 怎么让路由器ttl=100刷机

使用网线,连接电脑和路由器的wan口

把usb转TTL线连接到电脑USB端口,另一端连接到路由器的TTL接口。接线方法
接线 路由器上VCC 不接
路由器 Tx --- TTL线的RX针
路由器 Rx --- TTL线的TX针
路由器GND --- TTL线的GND针

安装usb转ttl 串口驱动。
在设备管理里面,要看到COM3出现;
把电脑网口IP配置为192.168.1.100;
安装TFTP 配置TFTP软件,刷机文件要放在TFTP指定目录下。

配置串口终端。运行putty,点Serial,串口设置: 波特率 57600,NONE,8,1,NONE。
打开串口,开始显示路由器开机过程。

路由器通电;U-Boot 1.1.3 config usb.. 10、在出现"config usb.."文字时,按“2”;******************************Software System Reset Occurred ****************************** __________________________________________________________________ | ______ ___ ____ ___ _ _ | | / ___\ \ / / \ |___ \ / _ \/ / | ___ ___ _ __ ___ | | | | _ \ \ /\ / / _ \ __) | | | | | | / __/ _ \| '_ ` _ \ | | | |_| | \ V V / ___ \ / __/| |_| | | || (_| (_) | | | | | | | | \____| \_/\_/_/ \_\_____|\___/|_|_(_)___\___/|_| |_| |_| | | | | Global Wireless Alliance | | http://www.gwa2011.com | | E-Mail:2579131212@qq.com | | Dreambox Team 2012 | |________________________________________________________________| Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.

You choosed 2
0 eth_register Eth0 (10/100-M) enetvar=ethaddr,Eth addr:00:0C:43:09:26:BB eth_current->name = Eth0 (10/100-M) 2: System Load Linux Kernel then write to Flash via TFTP. Warning!! Erase Linux in Flash then burn new one.
Are you sure?(Y/N) 输入“Y”,

并按照下面输入相应信息:Please Input new ones /or Ctrl-C to discard Input device IP (192.168.1.1) ==:192.168.1.1 Input server IP (192.168.1.100) ==:192.168.1.100
Input Linux Kernel filename () ==:0223.bin输入回车,刷机开始开始刷机。正确TFTP传输文件时,电脑TFTP上面会显示如下信息,表明TFTP开始传输文件
。 TFTP文件传输完毕。路由器删除FLASH,并将固件写入FLASH。

6
刷机完成后,路由器会重启,重启完毕,在TTL串口putty里面,输入回车,会显示如下信息,表明刷机已经成功:BusyBox v1.15.3 (2013-02-23 13:25:51 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. ______ ___ ____ ___ _ _ / ___\ \ / / \ |___ \ / _ \/ / | ___ ___ _ __ ___ | | _ \ \ /\ / / _ \ __) | | | | | | / __/ _ \| '_ ` _ \ | |_| | \ V V / ___ \ / __/| |_| | | || (_| (_) | | | | | | \____| \_/\_/_/ \_\_____|\___/|_|_(_)___\___/|_| |_| |_| ------Dreambox-GWA(2013, r570) ------------ * 全球无线联盟 哦耶 * Global Wireless Alliance, AE * http://www.gwa2011.com * Mail:[email protected] * Powered by Openwrt-Dreambox 2013 ------------------------------------------------root@AE:/#

阅读全文

与puttyttl传文件相关的资料

热点内容
五轴编程圆心点和对刀点怎么用 浏览:471
txt编程怎么运行 浏览:693
软件文件位置的卸载 浏览:563
魅族手机通讯录文件 浏览:953
2008升级到2012 浏览:649
spring获取配置文件 浏览:827
puttyttl传文件 浏览:994
苹果5s换硬盘多少钱 浏览:165
word文件名的下划线在哪里 浏览:969
为什么网络出现错误 浏览:234
neta的密码 浏览:789
日历javascript 浏览:49
javakeytool下载 浏览:533
计算机数据挖掘过程包括哪些内容 浏览:489
扰乱网络道德秩序的行为有哪些 浏览:341
电影评论类网站怎么区分好 浏览:418
最新云南省行政区划代码 浏览:699
凯越地图升级 浏览:578
中心化数据库如何避免有人赖账 浏览:648
sw安装好的文件夹是哪些 浏览:112

友情链接