導航:首頁 > 版本升級 > puttyttl傳文件

puttyttl傳文件

發布時間:2025-10-13 12:48:15

Ⅰ 怎麼讓路由器ttl=100刷機

使用網線,連接電腦和路由器的wan口

把usb轉TTL線連接到電腦USB埠,另一端連接到路由器的TTL介面。接線方法
接線 路由器上VCC 不接
路由器 Tx --- TTL線的RX針
路由器 Rx --- TTL線的TX針
路由器GND --- TTL線的GND針

安裝usb轉ttl 串口驅動。
在設備管理裡面,要看到COM3出現;
把電腦網口IP配置為192.168.1.100;
安裝TFTP 配置TFTP軟體,刷機文件要放在TFTP指定目錄下。

配置串口終端。運行putty,點Serial,串口設置: 波特率 57600,NONE,8,1,NONE。
打開串口,開始顯示路由器開機過程。

路由器通電;U-Boot 1.1.3 config usb.. 10、在出現"config usb.."文字時,按「2」;******************************Software System Reset Occurred ****************************** __________________________________________________________________ | ______ ___ ____ ___ _ _ | | / ___\ \ / / \ |___ \ / _ \/ / | ___ ___ _ __ ___ | | | | _ \ \ /\ / / _ \ __) | | | | | | / __/ _ \| '_ ` _ \ | | | |_| | \ V V / ___ \ / __/| |_| | | || (_| (_) | | | | | | | | \____| \_/\_/_/ \_\_____|\___/|_|_(_)___\___/|_| |_| |_| | | | | Global Wireless Alliance | | http://www.gwa2011.com | | E-Mail:2579131212@qq.com | | Dreambox Team 2012 | |________________________________________________________________| Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.

You choosed 2
0 eth_register Eth0 (10/100-M) enetvar=ethaddr,Eth addr:00:0C:43:09:26:BB eth_current->name = Eth0 (10/100-M) 2: System Load Linux Kernel then write to Flash via TFTP. Warning!! Erase Linux in Flash then burn new one.
Are you sure?(Y/N) 輸入「Y」,

並按照下面輸入相應信息:Please Input new ones /or Ctrl-C to discard Input device IP (192.168.1.1) ==:192.168.1.1 Input server IP (192.168.1.100) ==:192.168.1.100
Input Linux Kernel filename () ==:0223.bin輸入回車,刷機開始開始刷機。正確TFTP傳輸文件時,電腦TFTP上面會顯示如下信息,表明TFTP開始傳輸文件
。 TFTP文件傳輸完畢。路由器刪除FLASH,並將固件寫入FLASH。

6
刷機完成後,路由器會重啟,重啟完畢,在TTL串口putty裡面,輸入回車,會顯示如下信息,表明刷機已經成功:BusyBox v1.15.3 (2013-02-23 13:25:51 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. ______ ___ ____ ___ _ _ / ___\ \ / / \ |___ \ / _ \/ / | ___ ___ _ __ ___ | | _ \ \ /\ / / _ \ __) | | | | | | / __/ _ \| '_ ` _ \ | |_| | \ V V / ___ \ / __/| |_| | | || (_| (_) | | | | | | \____| \_/\_/_/ \_\_____|\___/|_|_(_)___\___/|_| |_| |_| ------Dreambox-GWA(2013, r570) ------------ * 全球無線聯盟 哦耶 * Global Wireless Alliance, AE * http://www.gwa2011.com * Mail:[email protected] * Powered by Openwrt-Dreambox 2013 ------------------------------------------------root@AE:/#

閱讀全文

與puttyttl傳文件相關的資料

熱點內容
五軸編程圓心點和對刀點怎麼用 瀏覽:471
txt編程怎麼運行 瀏覽:693
軟體文件位置的卸載 瀏覽:563
魅族手機通訊錄文件 瀏覽:953
2008升級到2012 瀏覽:649
spring獲取配置文件 瀏覽:827
puttyttl傳文件 瀏覽:994
蘋果5s換硬碟多少錢 瀏覽:165
word文件名的下劃線在哪裡 瀏覽:969
為什麼網路出現錯誤 瀏覽:234
neta的密碼 瀏覽:789
日歷javascript 瀏覽:49
javakeytool下載 瀏覽:533
計算機數據挖掘過程包括哪些內容 瀏覽:489
擾亂網路道德秩序的行為有哪些 瀏覽:341
電影評論類網站怎麼區分好 瀏覽:418
最新雲南省行政區劃代碼 瀏覽:699
凱越地圖升級 瀏覽:578
中心化資料庫如何避免有人賴賬 瀏覽:648
sw安裝好的文件夾是哪些 瀏覽:112

友情鏈接